PRODUCTS

A633 Carbon Steel Coil

A633 Carbon Steel Coil

ASTM A633 steel includes four grades: A, C, D, and E, of which the thickness of grade C can reach 4 inches and the thickness of grade E can reach 6 inches. ASTM A633 steel specification is based on the standard specification for standardized high-strength low-alloy structural steel plate, which requires high notch toughness under low temperature conditions.

A572/S355JR Carbon Steel Coil

A572/S355JR Carbon Steel Coil

ASTM A572 carbon steel low-alloy steel is widely used as bridge panels, support plates, mechanical mounting plates, etc. for construction equipment, transmission towers, racks and other equipment.

Hot Dip Galvanized Coil

Hot Dip Galvanized Coil

Hot dip galvanizing is to make the molten metal react with the iron substrate to produce an alloy layer, so that the substrate and the coating are combined. Hot galvanizing is to pickle the steel and iron parts first. In order to remove the iron oxide on the surface of the steel and iron parts, after pickling, it is cleaned by ammonium chloride or zinc chloride aqueous solution or ammonium chloride and zinc chloride mixed aqueous solution tank, and then sent into the hot dip plating tank. Hot-dip galvanizing has the advantages of uniform coating, strong adhesion and long service life.

A204 Pressure Vessel Carbon Steel Coil

A204 Pressure Vessel Carbon Steel Coil

ASTM A204 boiler vessel coil is molybdenum alloy steel coil, mainly suitable for welding boiler and high temperature pressure vessel. According to the molybdenum content, ASTM A204 boiler vessel coil is divided into 3 grades: A, B and C. ASTM A204 The thickness of the boiler vessel coil is limited only by the ability of the chemical composition to meet the specified mechanical property requirements.

DIN 17100 ST37/ST52 Carbon Steel Coil

DIN 17100 ST37/ST52 Carbon Steel Coil

DIN 17100 steel coils are suitable for flange beams, steel bars, steel strips, steel plates, wide flat steel, seamless steel pipes and welded steel pipes, square and rectangular hollow profiles. According to standards, DIN 17100 steel plates are used for welding, riveting and threaded structural parts. Except for stress relief heat treatment and normalizing, it is not used for heat treatment.

A283/Q195 Carbon Steel Coil

A283/Q195 Carbon Steel Coil

ASTM A283 is a carbon steel coil used for general structural purposes. The steel has low and medium tensile strength. The ASTM A283 steel specification covers four structural quality grades of mild steel, grades A, B, C, and D, for general application.

A656/S355J2 Carbon Steel Coil

A656/S355J2 Carbon Steel Coil

ASTM A656 steel coil is a high-strength low-alloy steel used in structural applications. In structural applications, light weight and good formability are essential. ASME A656 steel plates are manufactured in different grades of 50, 60, 70 and 80 steel coils with specified yield points.

Z120 Galvanized Coil

Z120 Galvanized Coil

Z120 is the coating name, which means that the coating thickness on both sides is approximately 120g/㎡ or 36g/㎡ (three-point test) and 90g/㎡ (single-point test). Z120 grade galvanized steel coil is coated with zinc to make it more durable. The working principle of the process is to immerse the coiled steel plate in a galvanizing tank filled with molten zinc. Through the continuous galvanizing process of the thin steel sheet, the galvanized coil is obtained. This type of steel has better formability and good paint adhesion in commercial or architectural use. Another method of producing galvanized steel sheet is through a hot-dip plating process. In this method, it is essential that the steel sheet is heat-treated at 500°C immediately after the exit of the can to form the alloy film coating.

Galvanized Coil

Galvanized Coil

Galvanized steel is a type of steel that is coated with zinc for protection by an electroplating process. The galvanized layer is applied to cold rolled steel at low temperatures. So EG steel is also known as cold galvanized steel. Through electrolytic galvanizing, a uniform and dense zinc layer is finally formed on the surface of the steel, but the mechanical properties of the material are still maintained. Electrogalvanized steel is usually sold in coil or sheet form. EG coil is a kind of material that can be cut, slitted and profiled for other purposes.

304 Stainless Steel Coil

304 Stainless Steel Coil

304 stainless steel is a kind of universal stainless steel material, rust resistance than 200 series of stainless steel material is stronger. High temperature resistance is also better, can be as high as 1000-1200 degrees. 304 stainless steel has excellent corrosion resistance and good intergranular corrosion resistance. For oxidizing acids, it is concluded in the experiment that 304 stainless steel has strong corrosion resistance in nitric acid with a concentration of less than or equal to 65% of the boiling temperature. It also has good corrosion resistance to alkali solution and most organic and inorganic acids.

< 1234...8 >
%E7%AC%AC%E4%B8%80%EF%BC%8C%E6%9C%80%EF%BC%8C%E4%BC%98%E7%A7%80%EF%BC%8C%E5%A2%9E%E5%BC%BA%EF%BC%8C%E4%B8%80%E6%B5%81%EF%BC%8C%E5%8D%93%E8%B6%8A%EF%BC%8C%E9%A2%86%E5%85%88%EF%BC%8C%E5%85%88%E8%BF%9B%EF%BC%8C%E5%BC%95%E9%A2%86

Sorry，当前栏目暂无内容!

您可以查看其他栏目或返回 首页

Sorry，The current column has no content!

You can view other columns or return Home

MAIN PRODUCTS

CONTACT INFORMATION

Tel：+86 15166584447

WhatsApp：+86 15166584447

Email：steel@zgsteelcoil.com

ADD：Liaocheng · Shandong ·China

Whatapp

WhatsApp

Wechat

WeChat

Get in Touch

Submit Message →

Copyright ©

Powered by CEGglobal  |  SEO | Privacy policy

【 Business license】